View HEF4069UBPN_7223797.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

5 mhz single-supply operational amplifier op183 rev. d information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent ri ghts of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2005 analog devices, inc. all rights reserved. features single supply: 3 v to 36 v wide bandwidth: 5 mhz low offset voltage: 1 mv high slew rate: 10 v/s low noise: 10 nv/hz unity gain stable input and output range includes gnd no phase reversal applications multimedia telecom adc buffers wide band filters microphone preamplifiers general description the op183 is a single-supply, 5 mhz bandwidth amplifier with slew rates of 10 v/s. it can operate from voltages as low as 3 v and up to 36 v. this combination of slew rate and bandwidth yields excellent single-supply ac performance, making this amplifier ideally suited for telecom and multimedia audio applications. the op183 also provides good dc performance with guaranteed 1 mv offset. noise is a respectable 10 nv/hz. supply current is only 1.2 ma per amplifier. this amplifier is well suited for single-supply applications that require moderate bandwidth even when used in high gain configurations. this makes it useful in filters and instrumenta- tion. the output drive capability and very wide full-power bandwidth of the op183 make it a good choice for multimedia headphone drivers or microphone input amplifiers. the op183 is available in a so-8 surface-mount package. it is specified over the extended industrial (?40c to +85c) temperature range. pin connection 1 2 3 4 8 7 6 5 op183 top view (not to scale) 00292-001 null ?in +in v? nc v+ out null figure 1. 8-lead narrow body soic (s suffix)
op183 rev. d | page 2 of 16 table of contents specifications..................................................................................... 3 electrical characteristics @ v s = 5 v......................................... 3 electrical characteristics @ v s = 3 v......................................... 4 electrical characteristics @ v s = 15 v.................................... 5 absolute maximum ratings............................................................ 6 esd caution.................................................................................. 6 typical performance characteristics ............................................. 7 applications..................................................................................... 13 offset adjust ............................................................................... 13 phase reversal............................................................................. 13 direct access arrangement ...................................................... 13 5 v only stereo dac for multimedia ..................................... 13 low voltage headphone amplifiers........................................ 14 low noise microphone amplifier for multimedia ............... 14 3 v 50 hz/60 hz active notch filter with false ground ..... 14 low voltage frequency synthesizer for wireless transceiver .................................................................................. 15 outline dimensions ....................................................................... 16 ordering guide .......................................................................... 16 revision history 5/05rev. c to rev. d updated format.................................................................. universal removed op283 ................................................................. universal updated outline dimensions ........................................................16 changes to ordering guide ...........................................................16 2/02rev. b to rev. c edits to features...........................................................................1 edits to general description...............................................1 edits to specifications......................................................... 2C3 edits to package type........................................................................4 edits to ordering guide...........................................................4 edits to absolute maximum ratings ...............................4 edits to outline dimensions ...............................................12 revision 0: initial version
op183 rev. d | page 3 of 16 specifications electrical characteristics @ v s = 5 v t a = 25c, unless otherwise noted. table 1. parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = 2.5 v, v out = 2.5 v, 0.025 1.0 mv ?40c t a +85c 1.25 mv input bias current i b v cm = 2.5 v, v out = 2.5 v, 350 600 na ?40c t a +85c 430 750 na input offset current i os v cm = 2.5 v, v out = 2.5 v, na ?40c t a +85c 11 50 na input voltage range 0 3.5 v common-mode rejection ratio cmrr v cm = 0 to 3.5 v ?40c t a +85c 70 104 db large signal voltage gain a vo r l = 2 k, 0.2 v o 3.8 v 100 v/mv offset voltage drift v os /t 4 v/c bias current drift i b /t ?1.6 na/c output characteristics output voltage high v oh r l = 2 k to gnd 4.0 4.22 v output voltage low v ol r l = 2 k to gnd 50 75 mv short-circuit limit i sc source 25 ma sink 30 ma power supply power supply rejection ratio psrr v s = 4 v to 6 v, ?40c t a +85c 70 104 db supply current/amplifier i sy v o = 2.5 v, ?40c t a +85c 1.2 1.5 ma supply voltage range v s 3 18 v dynamic performance slew rate sr r l = 2 k 5 10 v/s full power bandwidth bwp 1% distortion >50 khz settling time t s to 0.01% 1.5 s gain bandwidth product gbp 5 mhz phase margin m 46 degrees noise performance voltage noise e n p-p 0.1 hz to 10 hz 2 v p-p voltage noise density e n f = 1 khz, v cm = 2.5 v 10 nv/hz current noise density i n 0.4 pa/hz
op183 rev. d | page 4 of 16 electrical characteristics @ v s = 3 v t a = 25 c, unless otherwise noted. table 2. parameter symbol conditions min typ max unit input characteristics offset voltage v os v cm = 1.5 v, v out = 1.5 v, 0.3 1.0 mv ?40c t a +85c 1.25 mv input bias current i b v cm = 1.5 v, v out = 1.5 v, 350 600 na ?40c t a +85c 750 na input offset current i os v cm = 1.5 v, v out = 1.5 v, na ?40c t a +85c 11 50 na input voltage range 0 1.5 v common-mode rejection ratio cmrr v cm = 0 v to 1.5 v, ?40c t a +85c 70 103 db large signal voltage gain a vo r l = 2 k, 0.2 v o 1.8 v 100 260 v/mv output characteristics output voltage high v oh r l = 2 k to gnd 2.0 2.25 v output voltage low v ol r l = 2 k to gnd 90 125 mv short-circuit limit i sc source 25 ma sink 30 ma power supply power supply rejection ratio psrr v s = 2.5 v to 3.5 v, ?40c t a +85c 60 113 db supply current/amplifier i sy ?40c t a +85c, v o = 1.5 v 1.2 1.5 ma dynamic performance gain bandwidth product gbp 5 mhz noise performance voltage noise density e n f = 1 khz, v cm = 1.5 v 10 nv/hz
op183 rev. d | page 5 of 16 electrical characteristics @ v s = 15 v t a = 25c, unless otherwise noted. table 3. parameter symbol conditions min typ max unit input characteristics offset voltage v os 0.01 1.0 mv ?40c t a +85c 1.25 mv input bias current i b 300 600 na ?40c t a +85c 400 750 na input offset current i os ?40 t a +85c 11 50 na input voltage range ?15 +13.5 v common-mode rejection ratio cmrr v cm = ?15 v to +13.5 v, C40c ta +85c 70 86 db large signal voltage gain a vo r l = 2 k 100 1000 v/mv offset voltage drift v os /t 3 v/c bias current drift i b /t ?1.6 na/c long-term offset voltage v os note 1 1.5 mv output characteristics output voltage high v oh r l = 2 k to gnd, ?40c t a +85c 13.9 14.1 v output voltage low v ol r l = 2 k to gnd, ?40c t a +85c ?14.05 ?13.9 v short-circuit limit i sc source 30 ma sink 50 ma open-loop output impedance z out f = 1 mhz, a v = +1 15 power supply power supply rejection ratio psrr v s = 2.5 v to 18 v, ?40c t a +85c 70 112 db supply current/amplifier i sy v s = 18 v, v o = 0 v, ?40c t a +85c 1.2 1.75 ma supply voltage range v s 3 18 v dynamic performance slew rate sr r l = 2 k 10 15 v/s full power bandwidth bw p 1% distortion 50 khz settling time t s to 0.01% 1.5 s gain bandwidth product gbp 5 mhz phase margin m 56 degrees noise performance voltage noise e n p-p 0.1 hz to 10 hz 2 v p-p voltage noise density e n f = 1 khz 10 nv/hz current noise density i n 0.4 pa/hz 1 long-term offset voltage is guarante ed by a 1,000 hour life test perfor med on three indepe ndent lots at 125 c, with an ltpd of 1.3.
op183 rev. d | page 6 of 16 absolute maximum ratings table 4. parameter rating supply voltage 18 v input voltage 18 v differential input voltage 1 7 v output short-circuit durati on to gnd indefinite storage temperature range s package ?65c to +150c operating temperature range op183 ?40c to +85c junction temperature range s package ?65c to +150c lead temperature range (soldering 60 sec) 300c 1 for supply voltages less than 7 v, the absolute maximum input voltage is equal to the supply voltage. maximu m input current should not exceed 2 ma. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. absolute maximum ratings apply to packaged parts, unless otherwise noted. table 5. package type ja 1 jc units 8-lead soic (s) 158 43 c/w 1 ja is specified for worst-case conditions; in other words, ja is specified for device soldered in circuit board for soic packages. esd caution esd (electrostatic discharge) sensitive device. electrostatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge wi thout detection. although this product features proprietary esd protection circuitry, permanent dama ge may occur on devices subjected to high energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality.
op183 rev. d | page 7 of 16 typical performance characteristics 80 70 60 50 40 30 20 10 0 quantity ?600 ?400 ?200 0 200 400 600 input offset voltage ( v) v s = 5v 300x op amps 00292-002 figure 2. op183 input offset voltage distribution @ 5 v 80 70 60 50 40 30 20 10 0 quantity ?600 ?400 ?200 0 200 400 600 input offset voltage ( v) v s = 5v 300x op amps 00292-003 figure 3. op183 input offset voltage distribution @ 15 v 160 140 120 100 80 60 40 20 0 quantity (amplifiers) 02468101 tcv os ( v/c) 00292-004 2 ?40c = t a +85c 300x op amps plastic package figure 4. op183 input offset voltage drift (tcv os ) distribution @ 5 v 160 140 120 100 80 60 40 20 0 quantity (amplifiers) 0246 8101 tcv os ( v/c) 2 ?40c = t a +85c 300x op amps plastic package 00292-005 figure 5. op183 input offset voltage drift (tcv os ) distribution @ 15 v 3 2 1 0 maximum output swing (v p-p) 1k 10k 100k 1m 10m frequency (hz) 00292-006 t a = 25c r l = 2k v s = 3v figure 6. op183 maximum output swing vs. frequency @ 3 v 3 2 1 0 maximum output swing (v p-p) 1k 10k 100k 1m 10m frequency (hz) 00292-007 t a = 25c r l = 2k v s = 5v 5 4 figure 7. op183 maximum output swing vs. frequency @ 5 v
op183 rev. d | page 8 of 16 15 10 5 0 maximum output swing (v p-p) 1k 10k 100k 1m 10m frequency (hz) 00292-008 30 20 25 t a = 25c r l = 2k v s = 15v figure 8. op183 maximum output swing vs. frequency @ 15 v 1 100m 10m 1m output voltage to rail (v) 1 10 100 1m 10m load current (a) 00292-009 sink source figure 9. output voltage vs. sink & source current 600 500 400 300 200 100 0 input bias current (na) ?15 ?10 ?5 0 5 10 13.5 common mode voltage (v) 00292-010 t a = 25c v s = 15v figure 10. input bias current vs. common-mode voltage 500 400 300 200 100 0 input bias current (na) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-011 v s = +3v v s = 15v, v s = +5v 100 125 figure 11. input bias current vs. temperature 1.50 1.00 0.75 0.50 0.25 0 supply current amplifier (ma) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-012 100 125 1.25 v s = 18v r l = v s = +3v r l = v s = +5v r l = figure 12. supply current per amplifier vs. temperature 1.50 1.00 0.75 0.50 0.25 0 supply current amplifier (ma) 0 2.5 5.0 7.5 10.0 12.5 15.0 supply voltage (v) 00292-013 17.5 20.0 1.25 t a = 25c figure 13. supply current per amplifier vs. supply voltage
op183 rev. d | page 9 of 16 60 40 30 20 10 0 short-circuit current (ma) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-014 100 125 50 ?1 sc +1 sc figure 14. short-circuit current vs. temperature @ 5 v 60 40 30 20 10 0 short-circuit current (ma) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-015 100 125 50 ?1 sc +1 sc figure 15. short-circuit current vs. temperature @ 15 v 140 100 60 20 common-mode rejection (db) 100 1k 10k 100k 1m frequency (hz) 00292-016 t a = 25c v s = 15v 120 80 40 0 figure 16. common-mode rejection vs. frequency 140 100 60 20 common-mode rejection (db) 100 1k 10k 100k 1m frequency (hz) 00292-017 t a = 25c v s = 15v 120 80 40 0 +psrr ?psrr figure 17. power supply rejection vs. frequency 80 40 20 0 gain (db) 1k 10k 100k 1m 10m frequency (hz) 00292-018 60 30 10 ?10 90 50 70 90 0 195 45 ?45 phase (degrees) t a = 25c v s = 3v r l = 10k gain phase phase margin = 43 figure 18. open-loop gain and phase vs. frequency @ 3 v 80 40 20 0 gain (db) 1k 10k 100k 1m 10m frequency (hz) 00292-019 60 30 10 ?10 90 50 70 90 0 195 45 ?45 phase (degrees) t a = 25c v s = 5v r l = 10k gain phase phase margin = 46 figure 19. open-loop gain and phase vs. frequency @ 5 v
op183 rev. d | page 10 of 16 80 40 20 0 gain (db) 1k 10k 100k 1m 10m frequency (hz) 00292-020 60 30 10 ?10 90 50 70 90 0 195 45 ?45 phase (degrees) t a = 25c v s = 15v r l = 10k gain phase phase margin = 56 figure 20. open-loop gain and phase vs. frequency @ 15 v v s = +5v r l = 2k v s = 15v or v s = +3v r l = 2k 1000 900 800 700 600 500 400 300 200 open-loop gain (v/mv) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-021 100 125 100 0 figure 21. open-loop gain vs. temperature 50 30 10 ?10 closed-loop gain (db) 1k 10k 100k 1m 10m frequency (hz) 00292-022 t a = 25c v s = 15v 40 20 0 ?20 a v = 100 a v = 10 a v = 1 figure 22. closed-loop gain vs. frequency 25 20 15 10 5 slew rate (v/ s) ?75 ?50 ?25 0 25 50 75 temperature (c) 00292-023 100 125 0 v s = 15v r l = 2k slew rate v s = 15v r l = 2k slew rate figure 23. slew rate vs. temperature 25 20 15 10 5 voltage noise density (na hz) 10 100 1k 10k frequency (hz) 00292-024 0 30 t a = +25c v s = 15v or v s = +3v, +15v figure 24. voltage noise density vs. frequency 5 4 3 2 1 current noise density (pa hz) 10 100 1k 10k frequency (hz) 00292-025 0 6 t a = 25c v s = 15v or v s = +3v, +15v figure 25. current noise density vs. frequency
op183 rev. d | page 11 of 16 90 50 30 10 impedance ( ) 100 1k 10k 100k 1m frequency (hz) 00292-026 70 40 20 0 100 60 80 t a = 25c v s = 15v av = 10 av = 1 00292-029 figure 29. small signal performance @ 15 v figure 26. closed-loop output impedance vs. frequency negative edge positive edge 80 70 60 50 40 30 20 10 0 small signal overshoot (%) 0 100 200 300 capacitance (pf) 00292-027 t a = 25c v s = 5v r l = 10k 00292-030 figure 30. 0.1 hz to 10 hz noise @ 2.5 v figure 27. small signal overshoot vs. load capacitance 00292-031 00292-028 figure 28. large signal performance @ 15 v figure 31. 0.1 hz to 10 hz noise @ 15 v
op183 preliminary technical data rev. d | page 12 of 16 op183 v s = 2.5v a v = +1 r f = 0 v in = 1v rms 80khz low-pass filter 600 1k 2k 5k 10 no load 0.1 0.010 0.001 0.0005 distortion (%) 20 100 1k 10k 20k frequency (hz) 00292-032 figure 32. thd + noise vs. frequency for various loads
op183 rev. d | page 13 of 16 applications offset adjust figure 33 shows how the offset voltage of the op183 can be adjusted by connecting a potentiometer between pins 1 and 5, and connecting the wiper to v ee . the recommended value for the potentiometer is 10 k. this will give an adjustment range of approximately 1 mv. if a larger adjustment span is desired, a 50 k potentiometer will yield a range of 2.5 mv. 1 4 5 2 6 3 op183 v ee v cc 7 v os 00292-033 figure 33. op183 offset adjust phase reversal the op183 is protected against phase reversal as long as both of the inputs are within the range of the positive supply and the negative supply ?0.6 v. if there is a possibility of either input going beyond these limits, however, the inputs should be protected with a series resistor to limit input current to 2 ma. direct access arrangement the op183 can be used in a single supply direct access arrangement (daa) as shown in figure 34 . this figure shows a portion of a typical daa capable of operating from a single 5 v supply; with minor modifications it should also work on 3 v supplies. amplifiers a2 and a3 are configured so that the transmit signal txa is inverted by a2 and not inverted by a3. this arrangement drives the transformer differentially so that the drive to the transformer is effectively doubled over a single amplifier arrangement. this application takes advantage of the ability of the op183 to drive capacitive loads and to save power in single-supply applications. op183 op183 op183 0.0047 f 3.3k 22.1k 750pf 20k 20k 20k 475 20k 0.1 f 37.4k 300pf 0.33 f 0.1 f 20k a3 a2 a1 rxa txa 2 .5v 00292-034 ref figure 34. direct access arrangement 5 v only stereo dac for multimedia the low noise and single-supply capability of the op183 are ideally suited for stereo dac audio reproduction or sound synthesis applications, such as multimedia systems. figure 35 shows an 18-bit stereo dac output setup that is powered from a single 5 v supply. the low noise preserves the 18-bit dynamic range of the ad1868. 8 4 2 1 3 op183 +? 220 f 47k 9.76k 100pf 7.68k left channel output 330pf 7.68k 5 7 6 op183 +? 220 f 47k 9.76k 100pf 7.68k right channel output 330pf 7.68k v l 1 ll 2 dl 3 ck 4 vbl 16 vol 15 agnd 14 vor 13 dr 5 v s 12 lr 6 11 dgnd 7 10 vbr 8 9 v ref 16-bit dac 18-bit serial reg. v ref 16-bit dac 18-bit serial reg. ad1868 00292-035 figure 35. 5 v only 18-bit stereo dac
op183 rev. d | page 14 of 16 low voltage headphone amplifiers figure 36 shows a stereo headphone output amplifier for the ad1849 16-bit soundport? stereo codec device. the pseudoreference voltage is derived from the common-mode voltage generated internally by the ad1849, thus providing a convenient bias for the headphone output amplifiers. 00292-036 op183 op183 op183 5v 5k optional gain 1k v ref l volume control 16 220 f 47k headphone left 5v r volume control 5k optional gain 1k v ref 16 220 f 47k headphone right ad1849 20 19 21 lout1l lout1r cmout v ref 10 f 10k 10k 10 f figure 36. headphone output ampl ifier for multimedia sound codec low noise microphone amplifier for multimedia the op183 is ideally suited as a low noise microphone preamp for low voltage audio applications. figure 37 shows a gain of 100 stereo preamp for the ad1849 16-bit soundport stereo codec chip. the common-mode output buffer serves as a phantom power driver for the microphones. 00292-037 op183 op183 5v 10k 10k ad1849 18 19 17 minl minr cmout 1/2 op219 5v 100 100 10k 10k 50 10 f 50 10 f 20 20 right electret condenser mic input left electret condenser mic input figure 37. low noise stereo microphone amplifier for multimedia sound codec 3 v 50 hz/60 hz active notch filter with false ground to process ac signals, it may be easier to use a false-ground bias rather than the negative supply as a reference ground. this would reject the power line frequency interference which can often obscure low frequency physiological signals, such as heart rates, blood pressures, eegs, and ecgs. figure 38 shows a 50 hz/60 hz active notch filter for eliminating line noise in patient monitoring equipment. it has several kilohertz bandwidth and is not sensitive to false-ground perturbations. the simple false-ground circuit shown achieves good rejection of low frequency interference using standard off- the-shelf components. 4 5 3 1 2 a1 8 7 6 op183 4 1 3 a3 r1 2.67k 3v c1 1 f r3 2.67k c2 1 f r4 2.67k r2 2.67k r5 1.33k (2.67k ? 2) c3 1 f (1 f 2) r8 1k r7 1k c5 0.015 f r12 70 r11 10k 0.75v c6 1 f r10 25k c4 1 f r9 75k 3v v in r6 10k v o 00292-038 a2 op183 op183 q = 0.75 note: for 50hz applications change r1?r4 to 3.1 and r5 to 1.58 (3.16 ? 2). figure 38. 3 v supply 50 hz/60 hz notch filter with pseudo ground amplifier a3 biases a1 and a2 to the middle of their input common-mode range. when operating on a 3 v supply, the center of the common-mode range of the op183 is 0.75 v. this notch filter effectively squelches 60 hz pickup at a filter q of 0.75. to reject 50 hz interference, change the resistors in the twin-t section (r1 through r5) from 2.67 k to 3.16 k. the filter section uses op183 op amps in a twin-t configuration whose frequency selectivity is very sensitive to the relative matching of the capacitors and resistors in the twin- t section. mylar is the material of choice for the capacitors, and the relative matching of the capacitors and resistors determines the filters pass-band symmetry. using 1% resistors and 5% capacitors produces satisfactory results.
op183 rev. d | page 15 of 16 low voltage frequency synthesizer for wireless transceiver the low noise and low voltage operation capability of the op183 serves well for the loop filter of a frequency synthesizer. figure 39 shows a typical application in a radio transceiver. the phase noise performance of the synthesizer depends on low noise contribution from each component in the loop as the noise is amplified by the frequency division factor of the prescaler. the resistors used in the low-pass filter should be of low to moderate values to reduce noise contribution due to the input bias current as well as the resistors themselves. the filter cutoff frequency should be chosen to optimize the loop constant. 3v op183 phase detector reference oscillator crystal prescaler rf out v control vco 900mhz 00292-039 figure 39. low voltage frequency synthesizer for a wireless transceiver 7 6 4 1 3 5 2 ba qb3 qb1 qb2 rb2 rb1 qb4 qb5a cb1 r10 r3lt r3at r3a r3b cc1 r4a r4b r11 r4lt r4at qb12 qb13 q1 q2 z1 r1 r2 jb1 qb9 qb10 qb6 rb3 rb4 rb5 rb6 qb7 q7 q8 qb8 q5 qd1 q6 q3 q4 cf1 r5 cc3 qb11 qd2 r9 q12 cc2 r8 qd3 co r7 q11 q10 qb14 00292-040 figure 40. op183 simplified schematic
op183 rev. d | page 16 of 16 outline dimensions 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) 0.50 (0.0196) 0.25 (0.0099) 45 8 0 1.75 (0.0688) 1.35 (0.0532) seating plane 0.25 (0.0098) 0.10 (0.0040) 4 1 85 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 1.27 (0.0500) bsc 6.20 (0.2440) 5.80 (0.2284) 0.51 (0.0201) 0.31 (0.0122) coplanarity 0.10 controlling dimensions are in millimeters; inch dimensions (in parentheses) are rounded-off millimeter equivalents for reference only and are not appropriate for use in design compliant to jedec standards ms-012-aa figure 41. 8-lead standard small outline package [soic_n] narrow body (r-8) s-suffix dimensions shown in millimeters and (inches) ordering guide model temperature range package description package option op183gs ?40c to +85c 8-lead soic_n s-suffix (r-8) op183gs-reel ?40c to +85c 8-lead soic_n s-suffix (r-8) op183gs-reel7 ?40c to +85c 8-lead soic_n s-suffix (r-8) op183gsz 1 ?40c to +85c 8-lead soic_n s-suffix (r-8) op183gsz-reel 1 ?40c to +85c 8-lead soic_n s-suffix (r-8) op183gsz-reel7 1 ?40c to +85c 8-lead soic_n s-suffix (r-8) 1 z = pb free part. ?2005 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. c00292-0-5/05(d)

▲Up To Search▲

Price & Availability of HEF4069UBPN

	To Download HEF4069UBPN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .